Features The Jensen XA4150 power amplifier is a two-. Bridgeable design to direct full power to two. Channel 400-watt total system power automotive. Jensen XA3022LX amp - I have a Jensen amp xa3022lx and it doesn't have the plug for the high level. I need to know what the pins are. There are 6 pins in this plug. I could make this work it I knew what the pins were. I know this amp works. I also know that it a little one but it will do the trick f.

®

How to Install and Operate the XA4150 Amplifier

®

PROTECT

Welcome!

What you're holding in your hands is no ordinary owner's manual. We've tried to make the instructions in this book clear and easy to follow.

For your Jensen amplifier to work right, it must be installed correctly. This manual will show you how to install your new amplifier like a pro. It's a good idea to read all of these instructions before you begin the installation. Most installations are straightforward and can be handled by a do-it-yourselfer with the right tools, patience, and the ability to follow instructions. But, do-it-yourself installation isn't for everyone. If you still don't feel confident after reading this book, consider turning the installation job over to someone better suited to it.

Warranty Service

If your Jensen amplifier should ever require service, you will need to have the original dated receipt. If you ever need to return the unit for any reason, always include the receipt with the product.

Technical Assistance

For technical assistance with the operation or installation of the XA4150, call 1-800-323-0221.

®

Installation

Before You Begin Installation

Before you begin, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you start. There is a list of supplies and tools on the next page.

Amplifier Location

Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

–

Important

Allow air circulation around the amplifier.

The XA4150 amplifier’s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk.

When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier. Do not cover the XA4150 with carpets or enclose it behind interior trim panels. Do not mount the amplifier in an inverted or upside down configuration. Every installation will be a bit different based upon vehicle design. Check all locations and placements carefully before making any cuts or connections.

Important

If wiring connections are made wrong, the unit will not operate properly and it could be damaged. Follow the installation instructions carefully, or have the installation handled by an experienced technician.

Professional Tip

Amplifier Installation Kit

Your installation job will be much easier if you purchase an amplifier installation kit. These kits often include low-level RCA cables, extra large power and ground wires, a fuse or circuit breaker and connector for the battery.

Supplies and Tools Needed

Supplies:

•Speaker wire (12 gauge for subwoofers, 16-18 gauge for other speakers)

•Sheet metal type screws for mounting amplifier

•Electrical tape

•Solderless crimp connectors

•1/2' thick plywood or particle board to mount amplifier on

Tools:

•Flat and Phillips screwdrivers

•Wire cutters

•Wire strippers

•Cordless or standard electric drill and drill bit set

•Crimping tool (if using solderless crimp connectors)

Jensen Xa 1120 Manual Download

•12-volt test light or digital multimeter

•Wire brush or scraper (to remove paint for a good ground connection to vehicle)

•Soldering iron and rosin core solder (if you're going to solder your connections)

Amplifier Installation Kit:

You will need an amplifier installation kit to install your amp properly because it contains all the wire and connectors that you will need to hook up your new amp right the first time. If you want to purchase these items separately you will need the following:

•20-25 feet of 8 gauge wire

•50 amp fuse or circuit breaker (to be hooked up at the battery)

•20 feet of 18 gauge wire for the remote turn-on/ power antenna lead

•RCA cable (for signal input from radio)

–20 feet for trunk installation

–12 feet for under-seat installation

•Two 8 gauge ring terminals (one for the battery connection and the other for the ground connection at the amp). You may need two additional ring terminals if you are using a circuit breaker at the battery.

•Two 8 gauge barrel connectors (you may need these depending on what type of fuse holder you have)

•Two 8 gauge spade terminals (to hook up power at the amp)

•Eight 12 gauge spade terminals for subwoofers or 16-18 gauge spade terminals for other speaker connections to amp

•One 18 gauge spade terminal for remote turn-on/ power antenna lead

Routing Wires

Battery

Battery

Connector

Fuse or Circuit

Breaker

Grommet

To prevent damage to power wire

Receiver

Power Wire

(8 gauge wire or larger)

Power Antenna Turn-on Wire

(18 gauge wire)

RCA Cables

Speakers

Jensen Xa 1120 Manual Diagram

Professional Tip

Bigger is better

Stereo installation dealers sell extra thick power and speaker wires to ensure best sound. Look for 8 gauge power wire, especially if you have several amplifiers.

®

Wiring

Power and Outputs

Jensen Xa 1120 Manual User

FUSE

POWER

Jensen Xa 1120 Wiring

Power Terminal (BATT +12V)

Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum).

+ 12V RMT GND

Ground Terminal (GND)

Connect to a good chassis ground. The ground connection should be to clean, unpainted metal to provide a good electrical connection.

Jensen Xa 1120 Manual Instructions

4

Remote Terminal (RMT +12V)

Connect the radio power antenna lead from the receiver to the amplifier remote (RMT) terminal. This turns the amplifier on whenever the receiver is turned on. If a power antenna lead is not available, connect this wire to the radio or accessory fuse.

Jensen Xa 1120 Manual Pdf

Jensen Xa 1120 Manual Instructions

Spade

Butt Connector Connector

(not supplied)

8 Gauge

Wire

To Receiver

Power

Antenna Lead

Fuses

FUSE

Use only two 25 amp blade-type fuses.

25A